Lake Murray, SC

A couple weeks back I headed out for another weekend of sailing and camping. I had originally planned to head back to Lake Marion again, but got a late start so halfway there I decided to try Lake Murray, which is just west of Columbia, SC. Lake Murray turned out to be a great lake for sailing, The weather was pretty heavy that first day with avg 15 knot winds with only a few gusts coming in but those that did were pretty heavy.

A fair bit of heeling even with just the main up

The whole day ended up being a close reach which I actually enjoyed quite a bit. Beam reaches are just too easy! I had the rail close to the water most of the day since my main sail is very full which works well in light air, but ends up causing a lot of heel. I started to put in reef points but haven't set the grommets yet. At one point after I had rolled out the genoa (I'm not much for caution), a good gust caught me which put the coaming all the way in the water and made me take on about ten gallons of water! Which pointed out the need to enlarge the cockpit drains. And got my feet wet. Fortunately my beer didn't spill so disaster averted. I also wanted to practice heaving to and learned that my boat will heave to quite nicely in strong winds which was good to know. I spent a fair bit of time looking for a good place to camp and finally found a quiet cove that already had a fire pit and settled in for the night.

The following morning was quite pretty and after a couple cups of coffee and some oatmeal I was ready to go. Unfortunately, the wind was not ready to cooperate.

What took about 3 1/2 hours to get out to, ended up taking the better part of almost 12 hours to get back. The wind had died overnight for the most part and shifted so I was back on a close reach which is no fun in light shifting winds. Only had a small trolling motor but worse I hadn't put back in the larger batteries so I was stuck trying to gather what wind I could and paddling to get somewhere. Ugh. You can see in the track below the straight line out and the much less fun track back. And the glassy conditions at times on the lake in the picture above. Ah well, it was still nice to get out and learned a few more tricks and made it back so all in all a good weekend.

Companionway Updates

I got some new bits on the boat today. The hatch on the Newport 16 is basically just a cover that sits on top, nothing to hold it down. So I got a couple of Sea Dog hatch hinges that have a removable pin in case I do want or need to take it off. I also got a twist type hatch adjuster to hold it open which will make it a lot easier to grab things from down below without climbing all the way in. At 6'3" the cabin is awfully tight so I like to just lean in. But then I don't quite clear the hatch with my back if I put a knee on the companionway sill, I had to move very slow and it was quite a pain.

You can also just see the new drop board bits I built which I'll get pics of later.

Sailing on Lake Marion - Day 2

Day two started with a beautiful sunrise. I made some coffee with the JetBoil french press and got going. Still no rudder but the wind had shifted a little and lightened up some so it wasn't hard to get out and get going. Mainly steering by my position on the boat occasionally hanging over the side to get it to turn windward. Without a rudder I had a lot of lee helm which was a hassle. After a nice long close hauled reach trying to steer through the stumps to the deeper water on the other side I got into a weird situation where I could not get the boat pointed. I finally rolled up the genoa and that helped balance things out although I did lose some speed. After a couple wasted tacks going nowhere, I got it settled into a nice groove and managed to get a couple good long tacks and then got a nice wind shift headed back to get up to the bridge.

The one long tack from Vance back across the lake looked like this and was the best part of the day. Note the lack of a tiller. I just sat with my back on the cabin occasionally leaning a little left or right to adjust my heading. The engine there became just for show since it wouldn't run after a bit, just started leaking gas. I was guessing that the float in the carb got stuck or some such. I am definitely going back to the trolling motor because it has been nothing but trouble.

I was ghosting my way under the bridge close hauled and just about through the second span when a gust of wind came up and grabbed the front of the boat, smashing the bow. Yay. Got a pretty good bit of damage to a spot that had already been repaired once prior to me, so now I get to repair it again for real. Slightly ironic in that I have a rub rail I am working on that will look nice ad would have been great protection for that but oh well. On the other side of the bridge the winds got flukey which are a real pain to deal with when you are steering by jumping around the boat. I did get a good wind for a while but I started figuring that it was going to be tight making it to the landing by dark and if the wind died I wasn;t going to make it. So I bailed out at a boat ramp with a nice beach next to it. Tied the boat off and got to enjoy a nice 8 mile run back to my car. Well I probably ran about 6 of it and walked 2, took me about an hour and 15 minutes or so. Well I did want to get some exercise this weekend.

All in all, it was quite an adventure. What is it they say, "It's not an adventure until something goes wrong." I was happy that despite all the setbacks the boat did get me back home in one piece and I learned quite a bit about the boat and how to sail it. I'd actually sail Lake Marion again. It was a nice wide lake, the camping was beautiful and there were plenty of spots to camp. The cypress trees are vary nice. I'd launch closer to 95 to avoid the hairy sections and try to generally stick to the south side where the main channel is (the blue line in the google earth pic above) to avoid the hazards.

The rest of my pictures are up on picasaweb at https://picasaweb.google.com/110586701752725030552/LakeMarion

Sailing on Lake Marion - Day 1

So I decided I would head down to Lake Marion in SC this weekend just to sail somewhere different. My local lake, Lake Norman is relatively narrow so the winds can be flukey. Plus I figured I would make a weekend of it and camp out on an island somewhere. Turned into quite the adventure, but I learned a lot about my boat and gained a few new skills. Plus any trip where you wake up to this view can't be all bad, right?

So here is a view of the google earth track. Navionics is a great little application (Lakes East is what I have), but I have heard the new version is not as good.

   There was a lot of wind, white caps on the lake, but overall not too bad. Probably should not have chosen to launch on the lee shore at a place called Stump Hole Landing though! It lived up to its name with a lot of stumps and in fact the whole lake has good stretches of stumps as well as cypress trees popping up. There was one lonely little tree right out in the middle of the lake. Considered changing my plans to come from the north side of the lake which would have made more sense. But I got out, had a great downwind run making over 4 knots with just the genoa out (the roller furler worked well although I need a longer reefing line!).
  I made it under 95 and got greedy and tried to hoist the mainsail. Well the new tiller tamer had been working great except that my tiller moves up and down so when I am not holding it it basically falls down and locks the tiller. So when I moved forward and was pulling the main up a good gust of wind came up, pushed the boat out of the wind and caught the sail. When the boat heeled over, I heard the crack of the rudder. The wind was pushing me hard into the shore for a while until I got things situated.
  So I got to to learn how to sail for the next 7 miles by playing with sail trim. I was losing light since I got a late start playing with things around the house, so I decided to hit a nice harbor I saw on the charts and just managed to glide up to a great little island and get everything on the shore and my tent set up in the last bit of light. I had a nice little spot and the Newport floated out in about 8 inches of water. Great sandy spot for my tent, sheltered from the wind and I slept like a baby, except at one point when my forearms got tight (from holding the sheets for two hours steering along) and I woke up with my hand asleep.

But again, got a perfect spot to camp and had a great night.

I wanted to post some pics of a new DIY roller furling setup. I got a lot of ideas from a post on the web that I can't seem to locate now. It's built out of mostly 1/2 inch sch 40 electrical conduit. I used conduit since it is made to be UV resistant as opposed to white PVC pipe. The T had to be gotten from the plumbing section as well as the two parts of the drum. About 25 bucks for the whole thing.

Here is the drum. This is the only part I glued together and even that doesn't absolutely need it. From the bottom it consists of a 1/2 inch cap, small bit of 1/2 pipe to connect, 1/2 male threaded piece, PVC box cap (from electrical dept.) 1/2 inch thread to 1 1/4 adapter, small bit of 1 1/4 to connect it to the next adapter, plate and male adapter, then the 1/2 inch pipe starts.



You can see where the 1/2 pipe starts I actually drilled and chamfered a small stainless (#6 x 1/2) screw rather than gluing. I had done this same design but glued all the pieces together but ended up breaking bits on it while moving the mast around and such. Using a screw does two things; allows me to take it apart and replace bits if needed and makes it slightly more flexible which will hopefully put a little less stress on things and I won't break it! We'll see how it holds up. If it all goes to heck, I can still take the jib off and hank it back on but it has held up rolling things up in about 25mph winds.

Here is the next bit. Basically cut pieces of PVC long enough to go in between the hanks, then cut out a bit of the coupling and pipe about halfway around to give room to get the hank on the fore stay. Then I put a screw in the backside of the coupling (could also be glued). Do this for each hank of course.



And here is the top bit, pretty self explanatory. Using eyebolts with washers, then zip tying the jib top and bottom. The whole thing just spins on the caps on either end, tension on the sail is preset by the zip ties and the pvc pipe between the hanks so you want to get it fairly tight. I also sized it so the caps roll on the swaged ends and not on the stay itself, it will roll smoother and less chance of damaging the stay that way.



Final step, go sailing!

The boat is in the water and sailing just fine. Still work to be done, but most of that will be waiting until wintertime.

Alright, so here is the cockpit sole getting ready to go back on. You can see I left spaces between some of the plywood cores. My theory being if one of them gets wet and starts to rot at least it won't be all of them.

I dropped it down and used 3M 5200 to seal it back together. Used about 125 3/16" Aluminum rivets and backing washers. Came out pretty well, not pretty to look at but solid.

And here it is looking like an actual boat again! I rigged up a mast taberknackle out of 3/4 plywood and some fiberglass, temporary until I break down and order the right parts from Dwyer Mast. That will push my costs up a good bit. I will put up a post with my cost breakdown soon, but suffice it to say I wasted some money on buying smaller quantities of things like epoxy and fiberglass resin by not breaking down and buying the right amount to begin with. Kind of a learning experience there, I was trying to save money but in the end there were some places I could have saved by spending more up front on supplies.

I did order a main sail from Bacon Sails which I haven't hoisted yet but looks pretty nice in the bag. A lot cleaner than the genoa that I have. At some point I will order a jib from them since that one is pretty rough.

If all goes well I will get it in the water this weekend for a test run. Need to finish hacking together the ruddder I am working on, hack up a boom and sheets, place cleats for said sheets, finish the transom, and get that keel bolted back in there. And don't worry, I will have an outboard for when all of that breaks and the mast falls off.

Obviously more to go before I will be content, mainly paint, rub rail, windows, a real rudder and boom. But making progress.

OK, so this is what is left after I removed the whole core from the cockpit deck. I didn't want to do this now, but the best time to do it was now when it was all apart. There was not one piece of good wood on this part, although the sides where the seats are is in good shape, so that's a small blessing. This isn't an expensive job if you do it yourself, but it is a lot of labor.

So I cut out all of the rotten wood and cleaned up the fiberglass. You can see at the top of the picture where I epoxied some aluminum corner channel which will sit at the centerboard trunk and deck junction. It will also give me a good spot to bolt the plates that will hold the centerboard.

Here you can see where I am epoxying some more aluminum around the hole where the cable to lift the keel comes through. I figured it would be stronger and corrode slower than wood at least. The rest of the deck I will core with 1/4 plywood and cover all of this with fiberglass, so we'll see. Hopefully with a good layer of 5200 adhesive caulk joining the centerboard trunk with the deck I won't get these leaks anymore and won't have to worry about it.

So I am making progress, I hope to have the majority of this epoxy work done by this weekend. You can also see I have hull 689, or if you read it upside down, it's hull 689.

I made some chain plates today. I wanted to do something besides fiberglass and epoxy for a bit, so I figured I would make the sidestay chain plates. These hold the lines that stabilize the mast on the sides for the non-nautical. I had bought a 4 foot piece of 1/8 aluminum corner stock, and just cut them out. A little grinding, a little drilling and some filing to clean it up and there you go. They should be made of stainless steel for the most strength but these should hold up for a while, and working with aluminum is a lot easier than stainless steel.

I wasn't going to spend any time on things like this until after the hull was back together, because if that doesn't go like I plan, what's the point. But I figured these would be very useful to hold the topside when I go to lower it back down on the boat and I already had the metal so why not.

I bought a Newport 16 this weekend. That might be an exageration in that I bought a hull, a mast, an old jib sail, and a trailer really. But what else do you need really? . And the two Icehouse beers in the bilge were just a bonus! OK, no, I did not drink them.

I guess I would say I am new to sailing but used to go out a lot on my grandfather's sunfish up in Michigan every summer, and I have a gaff rigged sail on my kayak I have been playing with lately. But nothing bigger than that. Hoping if this works out it will be a good boat to start with. Big enough for me and a couple others.

The whole seam between the hull and topside (except the transom) was broken and had been siliconed back together. Lots of fun cleaning that out. I built a lift and pulled the top off and am in the process of fixing some bad repairs and damage on the edges.

I have a few more pics here, on photobucket, http://s17.photobucket.com/albums/b75/tschmidty69/Newport%2016/

You can see where I started to prop up the front after separating it. It actually was held together by the silicon caulk but with a ton of gaps of course. I was originally going to just clean it out and try to epoxy it back together, but I decided after poking at it that it needed to just come apart to do the job right. Right now I have the bottom almost ready and need to start on the top. I've put in about 6 hours (including trips to the store) so far.

Suggestions for how to put it back together would be appreciated if anyone has any. My plan is to make sure both mating surfaces are flat. then epoxy and rivets, with washers on the bottom of the rivets. I don't see a huge need to through bolt it, it would be a bit stronger but more money.

Also wouldn't mind some details on rigging. I know boats will vary but curious how others have the blocks laid out, etc.

It really shouldn't be too long until I get it going, but we'll see. If not I have a trailer for my next boat!